May 17, 2019 · Structural Steel (AASHTO M270/ASTM A709) All structural steel will be AASHTO M270/ASTM A709 Grade 36 (F y = 36 ksi) or Grade 50 (F y = 50 ksi) and structural steel HP piling will be AASHTO M270/ASTM A709 Grade 50S (F y = 50 ksi) except where weathering steel (AASHTO M270/ASTM A709 Grade 50W steel) is indicated on the Design Layout or in special cases. See A709 Gr.36, A709 Gr.50, A709 Gr.50W, A709 GrA709 steel grade. A709 steel grade is a high strength low alloy structural carbon steel in quenching and tempering delivery station. A709 Gr.50W, A709 Gr.HPS50W/HPS70W, A709 Gr.100/100W steel plates have improved the property to anti- atmospheric corrosion. Gangsteel provides this grade plate in A6/A6M and A 709 adopt standard requirement.
Tool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. A709 Gr.50 Round Bar A709 Gr.50 Flat Bar A709 Gr.50 Hollow Bar A709 Gr.50 Tube / Pipe A709 Gr.50 Sheet / Plate A709 Gr.50 Strip / Coil A709 Gr.50 Wire A709 Gr.50 Forging A709 Gr.50 Tube / Pipe TEL:+86-80247006 A709 Grade 50W steel grade,A 709 Grade 50W Weathering ASTM A709 Grade 50W equal grade are EN10155 :S355K2G1W,NFA 35-502E 36 WB 4 .A709 Grade 50W is the specification used for steel plate used in the manufacture of bridges. BEBON can supply the stock steel grade A 709 Grade 50W Weathering Steel any need in A709 Grade 50W steel, pls contact us! Pre:S355 J2G2W weathering steel,S355J2G2W steel deliver condition. A709 Grade 50W steel grade,A 709 Grade 50W Weathering ASTM A709 Grade 50W equal grade are EN10155 :S355K2G1W,NFA 35-502E 36 WB 4.A709 Grade 50W is the specification used for steel plate used in the manufacture of bridges. BEBON can supply the stock steel grade A 709 Grade 50W Weathering Steel any need in
A709-50W (USA, AISI, ASTM, UNS ) - European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt ASTM A588 Grade A/B A709 Grade 50 W Ranger SteelASTM A588 Grade A/B A709 Grade 50 W. Also known as weathering steel, this grade will be used for products that are exposed to all weather elements. Used in Bridge Steel, freight cars, telecommunication towers, and gusset plates. This has atmospheric corrosion resistance that develops over time to ASTM A709 / A709M - 18 Standard Specification for
ASTM A709-50W is a standard specification for structural steel primarily in the fabrication of steel bridges. ASTM A709-50W covers high strength, low allow steel structural shapes, plates and bars. The atmospheric corrosion resistance of this steel in most environments is substantially better than carbon steel with or without copper addition. ASTM A709 Grade 50S|A709 Gr.50S steel plate__Steel Gangsteel Grade :A709 Grade 50S. Specification:Thickness 8mm-300mm, Width:1500-4020mm, Length:3000-27000mm. Standard:ASTM A709:Standard Specification for Structural Steel for Bridges ASTM A709 Grade HPS 50W steel plateProduct information. ASTM A 709/A 709M A709 Grade HPS 50W is a kind of weathering steel plate with Cr,Ni,Mo alloy when rolling. The low alloy steel plate A709 GR HPS 50W shall have an atmospheric corrosion resistance index of 6.0 or higher calculated from the heat analysis in according to steel guide G 101-predictive method based on the date of larabee and Coburn.When properly exposed to the
Specifications. Strength, Yield Strength ksi (MPa), Tensile Strength ksi (MPa):Stronger, 58-130 (400-900) Formability:% Elongation:Low for some grades, 14-21%. For better formability consider Drawing Steel. Joining Fair. ASTM A709/A709M-01a Datasheet -- ASTM International Grade 50W [345W], or HPS 50W [HPS 345W] shall not be substituted for Grades 36 [250], 50 [345] or 50S [345S] without agreement between the purchaser and the supplier. 1.3 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. ASTM A709/A709M-07 - Standard Specification for ASTM A709/A709M-07 Standard Specification for Structural Steel for Bridges. 1.1 This specification covers carbon and high-strength low-alloy steel structural shapes, plates, and bars and quenched and tempered alloy steel for structural plates intended for use in bridges. Nine grades are available in four yield strength levels as follows:
Grade 50W [345W], or HPS 50W [HPS 345W] shall not be substituted for Grades 36 [250], 50 [345] or 50S [345S] without agreement between the purchaser and the supplier. 1.3 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. ASTM Weathering Steel Specifications Central Steel ServiceASTM A709-50W is a standard specification for structural steel in bridges. ASTM A709-50W covers high strength, low allow steel structural shapes, plates and bars. The atmospheric corrosion resistance of this steel in most environments is substantially better than carbon steel with or without copper addition. ASTM A709-50W shall have an atmospheric corrosion index of 6.00 or higher. Keeping tabs on current ASTM specifications ARE YOU availability should be confirmed prior to specification. ASTM A709 provides toughness levels for three exposures and two uses. Much material supplied to A709 meets one of those toughness levels. Material furnished to ASTM A709 grades are acceptable for use where the
Chemical Composition. 0.25-0.27% Manganese*. 0.030-0.040% Sulfur max. 0.030-0.050% Silicon*. 0.40% max Copper min. 0.20%. * Manganese content of 0.85 to 1.35% and silicon content of 0.15 to 0.40% is required for grade 36 shapes with flange thickness over 3 in.