Otai Special Steel have more 16 years experience in GB 60SI2MN Spring Steel round bar, flat bar., rod bar, wire and plate supply. GB 60SI2MN Steel is a high quality Alloy Spring Steel, It belong to the high quality high carbon alloy Spring Steel. Quenched & Tempered Hardness is 28-34 HRc. 60SI2MN steel Annealing delivery hardenss less than 250HB. China Mild Steel Plate Structural Ms Carbon Steel Plate S355 structural steel plate is a high-strength low-alloy European standard structural steel covering four of the six "Parts" within the EN 10025 - 2004 standard. With minimum yield of 50,000 KSI, it meets requirements in chemistry and physical properties similar to ASTM A572 / 709.
AISI D2 is a cold work tool steel. Cold work dies steel D2 tool steel with high abrasion resistance, micro-deformation, the wind hard tool steel, carbon content as high as 1.5%, chromium content as high as 11.5%, the heat treatment hardness can reach 60 HRC. Otai Special Steel is Chinese d2 steel china supplier in steel round bar, plate, flat. D6 Tool Steel High-Carbon, High-Chromium, Cold-Work AISI D6 Steel Mechanical Properties. Poissons ratio 0.27-0.30; Izod impact unnotched 28.0 J; Elastic modulus 190-210GPa; AISI Cold D6 tool Steel Physical Properties. Density:7.85kg/cm3; Thermal Properties of AISI D6 alloy tool steel cold work. Thermal expansion:12 x 10-6/ºC, 20-100°C . Heat Treatment AISI Cold work alloy Steel D6 Datasheet for Steel Grades Carbon Steel AISI 4142information,mechanical properties, physical properties, mechanical properties, heat treatment, and Micro structure, etc. It also contains the use of AISI 4142,such as it is commonly used in bars, sheet,plates, steel coils, steel pipes,forged and other materials application. Datasheet for Steel Grades Carbon Steel AISI 4142 AISI 4142 Standard
May 30, 2020 · Properties with values for just one material (2, in this case) are not shown. For each property being compared, the top bar is EN 1.0038 steel and the bottom bar is SAE-AISI 1018 steel. EN 1.0038 (S235JR) Non-Alloy Steel SAE-AISI 1018 (G10180) Carbon Steel EN 10025-2 Material S235 Steel Properties, Equivalent Dec 14, 2019 · S235 Steel Properties. Since steel grade S235 is mainly divided into 3 quality grades, and different quality, the performance is slightly different, you may check the properties of these 3 quality grades through the links above. Physical Properties. Density:7.85g/cm3; Melting point:1420-1460 °C (2590-2660 °F) Mechanical Properties Equivalents of Carbon Steel QualitiesMesteel Is A B2b Portal. It Provides Steel And Construction Related Companies In The Middle East Information, News And An Extensive Interactive Database, Inclusive Offers And Inquiries.
Non-alloy quality steel Chemical composition of steel P265GH (1.0425), Standards of steel P265GH (1.0425) Mechanical Properties of steel P265GH (1.0425) Equivalent grades of steel P265GH (1.0425) steel P265GH (1.0425) Tensile Strength, Elongation, Proof strength , Hardness S235JR - OvakoGeneral Information. Soft structural steel easy to weld and bend. Variants suitability for hot dip zinc coating according the classification in Table 1 EN 10025-2:2004:Class 1: S235JR Chemical composition , S235JR - BEBON steelS235JR steel plate is one mainly of Carbon and low alloy steel, S235JR steel plate is a type of steel sheet under EN standard which is used to build ship, bridge, belongs to high strength sheet. EN10025-2 S235JR is equivalent to DIN:ST37-2,JIS:SS400,ASTM:A283C, GB Q235B and UNI:FE360B. For more information of S235JR steel plates, please check them in following:
S235JR Material Introduction EN 10025 S235JR material (1.0038 steel) is an European standard hot rolled non-alloy structural steel grade. It has good plasticity, toughness and weldability, certain strength and good cold bending properties.We have large quantities of S235JR Structural Steel - S235, S275, S355 Chemical Composition May 11, 2012 · Structural steel is a standard construction material made from specific grades of steel and formed in a range of industry-standard cross-sectional shapes (or Sections). Structural steel grades are designed with specific chemical compositions and mechanical properties eFunda:Properties of Carbon Steel AISI 1010Category :Steel:Class :Carbon steel:Type :Standard:Designations :France:AFNOR XC 10 Germany:DIN 1.1121 Japan:JIS S12C , JIS S1OC , JIS S9CK United States
General structural steel Material number:1.0038 / 1.0114 / 1.0117 Material name:S235JR / S235J0 / S235J2 Proprietary brand:® precidur S235JR /J0 /J2 Old name:St 37-2 Delivery specification:DIN EN 10025-2 Application:Steels for general mechanical engineering and steel structures with physical properties s235jr young modulus - Q235 Mild Carbon Steel PlateEN 1.0038 Steel S235JR Material Equivalent, Properties . EN 1.0038 material S235JRG2 or S235JR steel equivalent to US ASTM AISI SAE, European EN (German DIN, British BSI, France NF), ISO, Japanese JIS, Chinese GB, and Indian standard. yield strength 1 0037 - AH36 Steel SupplierEN 1.0038 Steel S235JR Material Equivalent, Properties Physical Properties of S235JR Steel (1.0038 Material) Material density:7.85g/cm3; Melting point:1420-1460 °C (2590-2660 °F) S235JR Steel (1.0038 Material) Mechanical Properties. The yield strength, tensile strength, elongation, and Charpy impact test are listed in the following data sheet.
Tool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S235JR Round Bar S235JR Flat Bar S235JR Hollow Bar S235JR Tube / Pipe S235JR Sheet / Plate S235JR Strip / Coil S235JR Wire S235JR Forging S235JR Tube / Pipe TEL:+86-80247006