A709 Structural, Carbon & HSLA Steel Plate - Chapel Steel. ASTM A709. A high-strength, low-alloy structural steel plate utilized primarily in the manufacture of bridges. Chapel Steel stocks A709 Grade 36, A709 Grade 50 and A709 Grade 50W. These grades are often specified with Charpy tests referencing the specific zone or lowest anticipated service temperature. ASTM A 709/A709M :2007 Standard Specification for 1.1 This specification covers carbon and high-strength low-alloy steel structural shapes, plates, and bars and quenched and tempered alloy steel for structural plates intended for use in bridges. Nine grades are available in four yield strength levels as follows:
ASTM A709 Structural Steel Plate for Bridges Leeco ® Steel stocks ample inventories of ASTM A709 steel plate in standard and high-performance grades. Overview:Common steel plate grade used primarily for the manufacture of bridges. Heavy thicknesses (3-inches or thicker) available at most Leeco Steel distribution centers. ASTM A709 Steel Plate - Grade 36, 50, 50W , HPS 50W , HPS Steel Plate Products. Carbon & High Strength Low Alloy (HSLA) Structural Steel Plate. A36; A572 Grade 42, 50, 60, 65; CSA G40.21 Grade 44W, 50W, 50A; A709 Grade 36 ASTM A709-A709M Steel Plate, Steel Bar, Steel Tubes ASTMA709 -It's used in carbon steel for bridges and low-alloy high-strength structural steels, plates and rods. 1.The steel number is basically the same as the alloy structural steel. 2.For professional use of low-alloy high-strength steel, it should be marked at the end of the steel number. For example, for 16Mn steel, special steel grades for bridges are
TJC Steel can supply A709 Grade 250/ A709 Gr250 High-Strength Low-Alloy Structural Steel Plate, mainly used in bridges building . Production Size:Thickness:4mm- 400mm; Width:1000mm- 4000mm; Length:4000mm- 12000mm. Production ability:10000 Tons Per Month. Production Way:Hot Rolled, Quenched( Q), Tempered( T) Techanical Details: ASTM A709/ A709M Grade 345 High-Strength Low-Alloy Chemical Composition (%):Mechanical Properties (Mpa) TJC Steel (owned by TJC Iron&Steel (Group) Co., Limited) is the most competitive manufacture and supplier of ASTM A709/ A709M Grade 345 High-Strength Low-Alloy Structural Steel Plates in China. For more details, please contact us freely. ASTM A709/A709M-07ASTM A709/A709M-03. April 2003. Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges. Historical Version.
1.1 This specification covers carbon and high-strength low-alloy steel structural shapes, plates, and bars, quenched and tempered alloy steel, and stainless steel for structural plates intended for use in bridges. Twelve grades are available in five yield strength levels as follows: ASTM A709/A709M-181.1 This specification covers carbon and high-strength low-alloy steel structural shapes, plates, and bars, quenched and tempered alloy steel, and stainless steel for structural plates intended for use in bridges. Twelve grades are available in five yield strength levels as follows: ASTM Weathering Steel Specifications Central Steel ServiceASTM A242. ASTM A242 is a high strength low-alloy structural steel specification with improved atmospheric corrosion resistance. This specification is normally applicable to steel plates through one-half inch in thickness. The atmospheric corrosion resistance of A242 is substantially better than that of carbon steels such as A36 and A572-50 with or without copper addition.
Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. B.S. 709 M 40 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join Supplier:[email protected] SA 516 Steel Plates Grade 60, 65 & 70 - American Alloy SteelWe produce fine grain steel plates (SA 516) for boilers and PVQ applications in Gr 60, 65 & 70. Contact us to discuss chemical and tensile requirements. Standard Specification for Structural Steel for Bridges
This specification covers carbon and high-strength low alloy steel structural shapes, plates and bars, and quenched and tempered alloy steel for structural plates intended for use in bridges. Heat analysis shall be used to determine the percentage of carbon, manganese, phosphorus, sulfur, silicon, and copper for the required chemical composition. Steel Grade Equivalents Table Universal Steel AmericaHOUSTON, TX. 1230 E. Richey Road Houston TX 77073 Toll Free 866.988.3800 CHICAGO, IL. 225 West Burville Road Crete IL 60417 ASTM A709 - SSABThe ASTM A709 is the Standard Specification for Structural Steel for Bridges and encompasses carbon, high-strength low-alloy, and quenched and tempered alloy steels used as structural plates in the construction of bridges. SSAB offers the following five grades of A709; 36, 50, 50W, HPS 50W and HPS 70W. The three weather grades of 50W, HPS 50W, and HPS 70W have an ASTM G101 enhanced